# Underfloor heating and oak flooring

> Can oak flooring go over underfloor heating? Surface temperature limits (~27°C), floor sensors, engineered vs 18mm solid oak and commissioning steps.

- URL: https://timbo.com.au/guides/underfloor-heating-oak-flooring
- Publisher: Timbo (https://timbo.com.au) – trade supplier of European oak floorboards to partners in Australia and New Zealand
- Last updated: 2026-10-14
- Contact (email only): partnerships@timbo.com.au

## Key facts

- Oak flooring can be used with underfloor heating when the system, adhesive and timber are all suitable and the floor surface is kept to about 27°C or less.
- A floor-surface or floor-probe temperature sensor is used to limit the surface temperature.
- Engineered timber is generally preferred over solid timber for underfloor heating.
- For Timbo's 18mm solid oak parquet, underfloor heating is conditional – talk to Timbo before specifying.
- Temperature changes should be gradual; rapid heating dries timber quickly and increases movement.

## The short answer

**Oak flooring can be used over underfloor heating, but the floor surface should be kept to about 27°C or less with a floor sensor, and engineered timber is generally preferred over solid** ([The Solid Wood Flooring Company](https://www.thesolidwoodflooringcompany.com/technical-article/underfloor-heating/)). For **18mm solid oak parquet** like Timbo's, underfloor heating is conditional – it depends on the heating system, controls, slab, adhesive and site conditions – so **talk to Timbo before specifying it**.

## Why heat is a challenge for timber

**Heat dries the air and the timber, and solid timber shrinks as it dries.** Underfloor heating puts the heat source right under the floor, so the timber can dry faster and further than in a conventionally heated room.

The main risks are:

- **Gapping** between blocks or boards as the timber dries.
- **Cupping or checking** if the top and bottom of the timber dry at different rates.
- **Adhesive stress** where the timber moves against the bond to the slab.
- **Hot spots** under rugs, furniture or where pipes or cables run close to the surface.

None of these are inevitable – they're controlled with surface temperature limits, gradual temperature changes, good moisture management and the right product.

## Engineered vs solid over underfloor heating

**Engineered timber is generally preferred for underfloor heating because its cross-layered core resists movement; solid timber can work in some systems but needs more care.**

| | Engineered oak | 18mm solid oak parquet |
| --- | --- | --- |
| Dimensional stability | Higher – core resists movement | Lower – moves more with moisture |
| Heat transfer | Often thinner, so heat passes more easily | Thicker – heat passes more slowly |
| Sanding life | Limited by wear layer | Many sands |
| Underfloor heating | Generally preferred | Conditional – talk to Timbo first |

Engineered oak is also commonly preferred for apartments, renovations and slab installations ([ArchiPro](https://archipro.com.au/products/finishes/flooring/wood-flooring/timber-flooring/material-oak)). More detail: [solid vs engineered oak](https://timbo.com.au/compare/solid-vs-engineered-oak).

## Key requirements

**The essentials are a surface temperature limit, a floor sensor, a dry slab, a compatible adhesive and gradual temperature changes.**

| Requirement | Why | Who sets it |
| --- | --- | --- |
| Floor surface ~27°C max | Limits drying and movement | Heating, adhesive and flooring manufacturers – most restrictive applies |
| Floor temperature sensor | Controls actual floor temperature, not just air | Heating designer |
| Dry slab before laying | Damp slab plus heat drives moisture into timber | Adhesive maker's test method and limit |
| Heated-floor-approved adhesive | Bond must tolerate temperature cycling | Adhesive maker |
| Gradual temperature changes | Avoids shocking the timber | Heating commissioning protocol |
| Even heat distribution | Avoids hot spots | Heating designer and installer |

## Commissioning and installation steps

**Run the heating before the floor goes down to dry the slab, then turn it down during installation and bring it back up slowly afterwards – following the heating and adhesive manufacturers' protocols.**

1. **Commission the system** once the slab or screed has cured, as the heating designer specifies, to drive out construction moisture.
2. **Test the slab** with the adhesive maker's method once it has cooled to their required temperature.
3. **Acclimatise the timber** in conditions that reflect heated use – see [acclimatising oak flooring](https://timbo.com.au/guides/acclimatising-oak-flooring).
4. **Reduce or switch off the heating** for installation and adhesive curing, as the adhesive maker requires.
5. **Lay the floor** with a heated-floor-approved adhesive – see [adhesives and moisture barriers](https://timbo.com.au/guides/adhesives-and-moisture-barriers) and [installing parquet over a concrete slab](https://timbo.com.au/guides/installing-parquet-over-concrete-slab).
6. **Restart gradually** after curing, increasing temperature in small steps over days rather than hours.
7. **Set the floor sensor limit** and hand over clear operating instructions to the owner.

## Living with a heated oak floor

- **Avoid sudden changes.** Bring the heating up slowly at the start of winter and down slowly in spring.
- **Keep indoor humidity steady.** Very dry winter air increases gapping. Typical Australian interiors sit at about 8–14% equilibrium moisture content ([WoodSolutions](https://www.woodsolutions.com.au/timber-wiki/moisture-guide)); heated floors tend toward the drier end.
- **Watch rugs and furniture.** Thick rugs, beanbags and solid-based furniture trap heat.
- **Expect some seasonal movement.** Small gaps that close again in humid months are normal.
- **Finish choice.** Both oils and polyurethane can be used; follow the finish maker's notes for heated floors. See [oil vs polyurethane](https://timbo.com.au/guides/oil-vs-polyurethane-finish).

## Questions for the heating designer

**Ask these before the floor is specified – they decide whether timber, and which timber, is suitable.**

1. **What type of system is it?** Hydronic pipes in the slab or a screed, electric mats or cables, or a panel system?
2. **What surface temperature will the floor reach** at design conditions, and how is it limited?
3. **Is there a floor sensor** in each zone, and where is it placed?
4. **How is the system commissioned** and how long must it run before flooring is installed?
5. **What's the heat-up and cool-down rate** the controls allow?
6. **Are pipes or cables evenly spaced** to avoid hot strips under the timber?
7. **Is the system approved by its maker** for use under timber floors – and under solid timber specifically?

Share the answers with your flooring installer, the adhesive manufacturer and Timbo. If any party can't confirm compatibility, consider an alternative floor or heating strategy for that area.

## Before you specify Timbo solid oak over underfloor heating

**Contact Timbo with the project details before specifying 18mm solid oak parquet over underfloor heating.** Useful information to have ready:

- Heating type (hydronic in-slab, electric mat, screed or other) and designer's details.
- Control system and whether a floor sensor is fitted.
- Slab age, thickness and moisture test results.
- Proposed adhesive system and its heated-floor approval.
- Room use, area and climate.

Timbo will tell you whether the solid product suits the job or whether another approach is better. Homeowners can raise this through a [Timbo partner](https://timbo.com.au/partners/find-a-partner).

**Talk to the Timbo team:** Questions about specifications, stock or partnering? We reply during business hours, Monday to Friday. → https://timbo.com.au/pages/contact-us

## Sources

- [The Solid Wood Flooring Company – Underfloor heating](https://www.thesolidwoodflooringcompany.com/technical-article/underfloor-heating/)
- [ArchiPro – Oak timber flooring](https://archipro.com.au/products/finishes/flooring/wood-flooring/timber-flooring/material-oak)
- [WoodSolutions – Moisture guide](https://www.woodsolutions.com.au/timber-wiki/moisture-guide)

## Frequently asked questions

### What is the maximum floor temperature for timber over underfloor heating?

A common limit is a floor surface temperature of about 27°C, controlled by a floor sensor. The heating system, adhesive and flooring manufacturers may set their own limits – the most restrictive applies.

### Is hydronic or electric underfloor heating better for oak floors?

Either can work if it's designed and controlled to keep the timber surface within limits. Hydronic systems in a slab respond slowly and give gentle, even heat; electric mats respond faster, so good controls and a floor sensor are essential. Check the timber and adhesive makers' compatibility notes for the system type.

### Can I put rugs on a heated timber floor?

Thick rugs trap heat and can push the surface temperature underneath above the limit, drying the timber locally. Use thin, breathable rugs and keep the floor sensor setting conservative.

### Do I need a special adhesive for parquet over underfloor heating?

Use an adhesive the manufacturer approves for heated floors and for solid parquet, and follow its instructions for slab moisture, heating shutdown during installation and restart afterwards.

### Will timber floors gap more with underfloor heating?

Usually somewhat more than unheated floors, because heated floors run drier in winter. Keeping temperature changes gradual, maintaining indoor humidity and starting with well-acclimatised timber reduce seasonal gaps.

## Related pages

- [Solid vs engineered oak flooring: differences, cost and which to choose](https://timbo.com.au/compare/solid-vs-engineered-oak) – Solid vs engineered oak flooring compared – construction, sanding life, stability on slab, underfloor heating, cost per m² and which to choose in AU or NZ.
- [Acclimatising oak flooring](https://timbo.com.au/guides/acclimatising-oak-flooring) – How to acclimatise oak flooring in Australia and NZ: equilibrium moisture content (EMC), ATFA figures, the ±2% rule, climate examples and a step-by-step method.
- [Adhesives and moisture barriers for timber flooring](https://timbo.com.au/guides/adhesives-and-moisture-barriers) – Adhesives and moisture barriers for solid oak parquet on slabs: adhesive types, moisture-barrier adhesives, separate barriers and why maker limits govern.