The short answer
Solid oak parquet on a concrete slab is glued with a timber flooring adhesive approved for solid wood, usually with either a moisture-barrier adhesive or a separate liquid moisture barrier, and the adhesive manufacturer's limits and instructions govern (Bowens). Choose one compatible system, test the slab the way that system requires, and follow its data sheets to the letter.
This page explains the options so retailers, installers and homeowners can ask the right questions. It doesn't replace the manufacturer's technical data.
What the adhesive has to do
A parquet adhesive must hold every block flat and tight to the subfloor, tolerate the timber's seasonal movement and resist moisture from below. Solid oak blocks are short, so each one depends on its bond – a poor bond shows up as hollow-sounding or lifting blocks.
| Requirement | Why it matters |
|---|---|
| Strong, durable bond | Holds short blocks flat |
| Some flexibility | Allows seasonal timber movement without bond failure |
| Moisture resistance | Limits moisture vapour from the slab into the timber |
| Compatibility | With the slab, primer/barrier, levelling compound and (if present) underfloor heating |
| Workability | Open time long enough to lay accurately |
Common adhesive types
Most timber flooring adhesives used for solid parquet on slabs are polyurethane or MS/silane-modified polymer (SMP) types; each manufacturer's products differ.
| Type | Typical characteristics | Notes |
|---|---|---|
| Polyurethane (1-part or 2-part) | Strong bond; some products also act as a moisture barrier | Check cure time, odour and clean-up |
| MS / silane-modified polymer | Elastic bond; often low odour and solvent-free; some include barrier properties | Check suitability for solid parquet and block size |
| Water-based | Low cost | Generally avoided for solid timber on slabs – adds water to the underside |
Exact performance – including slab moisture limits, trowel notch, spread rate, open time, foot-traffic time and sanding time – is product-specific. Read the data sheet.
Moisture-barrier adhesive vs separate barrier
A moisture-barrier adhesive is one product that bonds and limits moisture vapour up to a stated slab moisture level; a separate barrier (often an epoxy or similar liquid-applied coating) is used when slab moisture is above that level or the adhesive alone isn't rated for it.
| Moisture-barrier adhesive | Separate barrier + adhesive | |
|---|---|---|
| Steps | One | Two (barrier, then adhesive) |
| Slab moisture tolerance | Up to the adhesive's stated limit | Higher – up to the barrier's stated limit |
| Cost | Lower | Higher |
| Time | Faster | Barrier must cure before laying |
| Typical use | Slabs within the adhesive's limit | Higher-moisture slabs, ground floors, tight programmes |
Both are common Australian practice for glued timber floors on slabs. Neither fixes a slab that is wet because of a leak, missing membrane or poor drainage – find and fix that first.
How to choose a system
Start from the slab test results and the flooring product, then pick a system rated for both.
- Test the slab using the method the adhesive/barrier maker specifies – see installing parquet over a concrete slab.
- Check flatness and surface strength. Commonly within about 3mm under a 3m straightedge, with weak surface layers ground off.
- Compare readings with the limits of candidate adhesives and barriers. In New Zealand, BRANZ guidance also uses ≤75% RH at the slab surface for solid timber flooring (BRANZ BU644).
- Confirm the adhesive is rated for solid parquet and for your block size (Timbo's herringbone is 710 or 820 × 123 × 18mm).
- Check underfloor heating approval if there's heating – see underfloor heating and oak flooring.
- Use one manufacturer's system for primer/barrier, levelling compound and adhesive.
- Record products, batch numbers and test results in the job file.
Application tips
Most adhesive problems come from preparation and application, not the product.
- Prepare the slab properly – clean, sound, flat and free of curing compounds, paint and old adhesive.
- Use the specified trowel and replace it when the notches wear.
- Spread only what you can cover within the open time.
- Bed every block – press or tap down and check adhesive transfer by lifting one occasionally.
- Clean the face immediately with the adhesive maker's recommended cleaner; cured adhesive on raw oak can show through the finish.
- Respect cure times before sanding, finishing or heavy traffic.
- Mind the temperature – cold slabs slow curing; hot conditions shorten open time.
Adhesive problems and what they look like
Most bond problems show up as sound or movement – a hollow tap, a rocking block or a line of lifted joints.
| Symptom | Common causes | What to check |
|---|---|---|
| Hollow-sounding blocks | Insufficient adhesive, worn trowel, skinned-over adhesive, uneven slab | Trowel, open time, flatness |
| Lifting in one area | Moisture from slab or a leak | Slab moisture, plumbing, barrier |
| Blocks rocking at joints | Low spots in the slab | Flatness and levelling |
| Adhesive stains under finish | Residue left on raw face | Cleaning during laying |
| Widespread debonding | Wrong adhesive for slab moisture, contamination, curing compound | Product limits, slab preparation |
Investigate the cause before repairs – replacing blocks without fixing a moisture source simply repeats the failure.
Moisture barriers and timber moisture are different things
A barrier controls moisture coming from the slab; it doesn't make wet timber dry. The timber itself must still be acclimatised to within about ±2% of its in-service equilibrium moisture content (WoodSolutions). See moisture content in timber flooring and acclimatising oak flooring.
Where Timbo fits
Timbo supplies Prime grade European solid oak parquet to flooring businesses. Its partners choose and install the adhesive system that suits each site. For product dimensions and questions about using Timbo parquet with a particular system, contact Timbo.
Sources
- Bowens – Hardwood timber flooring
- BRANZ BU644 – Solid timber strip flooring on a concrete slab
- WoodSolutions – Moisture guide
Frequently asked questions
What adhesive is used for solid oak parquet?
Most solid oak parquet on slabs is laid with a timber flooring adhesive approved by its maker for solid wood – commonly polyurethane or MS/silane-modified polymer types. Check the adhesive is rated for solid parquet, your block size and your subfloor.
What is a moisture-barrier adhesive?
It's a timber flooring adhesive formulated to both bond the floor and limit moisture vapour from the slab, up to a stated slab moisture level. Above that level, the manufacturer will usually require a separate barrier.
Are water-based adhesives suitable for solid oak parquet?
Generally they are avoided for solid timber on slabs because they introduce water into the timber's underside. Only use an adhesive the manufacturer specifically approves for your product and subfloor.
Can I mix a barrier from one brand with an adhesive from another?
It's best not to. Manufacturers test and support their own systems; mixing brands can cause adhesion problems and may void the adhesive maker's support. Use a single compatible system.
What trowel should I use for parquet adhesive?
The one the adhesive manufacturer specifies for your product and block size. The trowel notch controls how much adhesive is spread and whether blocks get full contact – using the wrong one is a common cause of hollow blocks.